Need to keep two tanks cooling at once instead of just one? The BrewChill Pro 5500-2 ships with two 80 gal/hr vane pumps, each on its own 1/3 HP motor, so you can route glycol to two tanks simultaneously without adding a second chiller. Both pumps run off the same thermostat, so they hold to one shared setpoint - a good fit when two tanks need to sit at the same temperature at once, like a pair of fermenters or a fermenter and a bright tank. At 5,500 BTU/h, it holds fermenters and bright tanks up to 1,000 L exactly where you set them. A 1/2 HP compressor on R290 refrigerant keeps it quiet enough for a taproom floor and efficient enough for continuous use.
Key Features of BrewChill Pro 5500-2 Glycol Chiller
- Two-pump cooling standard: Two 80 gal/hr vane pumps on separate 1/3 HP motors - no upgrade needed to run glycol to two tanks at once, both held to the same setpoint.
- 5,500 BTU/h capacity: Built for USA craft breweries and small-batch producers running fermenters and bright tanks up to 1,000 liters.
- Low-noise compressor: A 1/2 HP compressor and R290 refrigerant keep cooling strong without excess noise or power draw.
- Sized for tight spaces: Fits microbreweries, taprooms, and serious homebrew setups without eating floor space.
- Quick install: 3/4"NPT fittings, 6-ft power cord, NEMA 5-20P plug for straightforward setup of this brewery equipment in a new or existing USA system.
- 450-ft glycol line reach: Flexibility to place tanks and chiller wherever your facility layout works best.
- 18-gallon tank, two pre-installed pumps: Built for continuous, high-demand brewing operations.
Parts Included:
- 1 × BrewChill Pro 5500 (80 GPH pump, 1/3 HP motor)
- 1 × External digital thermostat
- 4 × Solenoid valves
BrewChill Pro 5500 - USA |
|
| MODEL | BC-5500-2 |
| MAXIMUM DISTANCE | Up to 450 ft |
| CAPACITY | 5500 BTU/H |
| GLYCOL TANK CAPACITY | 18 gallons |
| COMPRESSOR POWER | 1/2 HP |
| RUNNING | 15 AMP |
| PLUG TYPE (NEMA #) | 5-15P |
| VOLTAGE | 115 V |
| FREQUENCY | 60 HZ |
| PUMP TYPE | Vane with 1/3hp motor |
| PUMP | 80 GPH |
| NUMBER OF PRE-INSTALLED PUMPS | 2 |
| NUMBER OF ADDITIONAL PUMPS | 0 |
| REFRIGERANT | R290 |
| REFRIGERANT CHARGE, G (OZ) | 150 (5.29) |
| WEIGHT GROSS/NET | 153 / 156 lb |
| POWER CORD LENGTH | 6 ft |
| INLET/OUTLET BARB, IN | red tube 3/4” NPT / blue tube 3/4” NPT |
| OPERATING AMBIENT TEMPERATURE | 60-90 F |
| CLEARANCE AT LEAST | 12" around the entire unit |
| GLYCOL MIXTURE, VOL% | 40 % glycol and 60% water |
Note: Installation of this item must be handled by a qualified installer in order to qualify for product return and/or warranty coverage. Qualified Installer - Defined as a licensed professional who charges a fee for his services and possesses a business license, contractor's license, and/or resale permit. Common examples of a "qualified installer" include Electrician; General Contractor; Heating and Air Conditioning Specialist.
Not sure which model is right for you? Our Brewery Glycol Chiller Sizing Calculator matches your tanks and process to the right capacity in a couple minutes. Got questions about sizing, specs or anything else? Get in touch and we'll help you sort it out.
Related Products
